Dormer Window Repairs
Leaks, rot, failed flashings, blown units and draughts — diagnosed and put right. Fix the cause, not the damp patch on the ceiling.
Dormer Window Repairs — indicative geometry
What a dormer window repair actually is
A stain on a dormer ceiling almost never starts at the window. It usually starts at the apron flashing, the cheek-to-roof soaker, the back gutter or a split in the flat roof covering, and travels. We trace the actual water path before quoting, because replacing a window that was never leaking is the most common wasted spend on a dormer.
Specification at a glance
| Common causes | Apron flashing, soakers, back gutter, split membrane |
|---|---|
| Diagnosis | Water trace before quotation |
| Rot repair | Splice or full replacement of sills and studs |
| Glazing | Blown unit replacement, any size |
| Draught proofing | Full seal and hardware replacement |
| Typical duration | 1–5 days |
How we build it
We would rather tell you at survey that your ridge height will not take what you want than take a deposit and find out in week three. Every dormer window repairs job runs the same seven stages — survey and feasibility, design and consent, scaffold and protection, structure, weatherproofing, glazing, then finish and sign-off.
Rear dormers on houses often sit inside permitted development, but the volume allowance is consumed by any previous loft or rear extension — so we check the planning history for the address before we say yes.
What is included in the price
- Measured survey, structural calculations and full working drawings
- Planning application or lawful development certificate, and the building regulations application
- Scaffold design, erection, weekly inspection, hire and dismantling
- All structure, weatherproofing, flashings, gutters and cladding
- Glazing with escape-compliant opening lights where required
- Building control inspections and your completion certificate
- Waste removal and making good
Where this goes wrong elsewhere
The two failures we are called to fix most often on dormer window repairs are undersized or incorrectly lapped flashings, and a vapour control layer that stops at the first awkward junction. Neither shows up for a winter or two. Both are cheap to do properly at build stage and expensive to correct afterwards.
The quickest route is a photograph of the rear elevation over WhatsApp — we can usually tell you what is feasible before anyone visits.
Related work
Dormer Window Repairs by county
Where we do this work
Specialist teams across 74 counties. Pick your area for local detail, or browse every town.
How a dormer gets built
Seven stages, in this order, every time
The sequence matters. Most dormer problems come from doing one of these out of order — glazing before the flashings, or opening the roof before the materials land.
Survey and feasibility
A specialist measures the roof, checks ridge height, span and structure, and confirms whether you are inside permitted development.
Design and consent
Measured drawings, elevations and sections. We submit the planning application or lawful development certificate and the building regulations application.
Scaffold and protection
Scaffold designed, erected and inspected. Temporary weather protection over the work area before anything is opened.
Structure
Ridge beam and floor steels craned or manhandled in, new joists laid, the dormer frame built and sheathed.
Weatherproofing
Deck, insulation, membrane or lead, cheek cladding, flashings and gutters — the dormer is weathertight from this point.
Glazing
Windows fitted square, sealed and drained, with escape-compliant opening lights where required.
Finish and sign-off
Plaster, electrics, decoration and making good, final building control inspection and your completion certificate.
FAQs
Dormer Window Repairs — your questions
Is scaffolding included in the price?
Yes. Every quotation we issue includes scaffold design, erection, weekly inspection, hire for the programme and dismantling. Scaffold appearing as an extra afterwards is one of the more common complaints about dormer work, so we price it in from the start.
Can you convert an existing Velux loft to a dormer?
Yes, and it is usually a shorter job than starting from scratch because the floor, staircase and services already exist. We verify the existing floor structure and any previous building control approval first, then cut and form the dormer into the finished room. Expect the room to be out of use for three to five weeks.
Do you work on listed buildings and in conservation areas?
Yes. That work is detail-led: matching sightlines, glazing bar widths, cill projections and cheek finishes to what survives, and specifying timber, lead and natural slate rather than modern equivalents. We prepare the drawings and heritage statement for listed building consent alongside the planning application.
What guarantees do you provide?
Structural work carries a ten-year guarantee, GRP and EPDM flat roofing twenty years, windows ten years on frames and sealed units, and lead and zinc work is covered for workmanship for ten years. You also receive the building control completion certificate, which is the document that actually matters when you sell.
Do dormer windows need to be fire escape windows?
In a loft conversion, at least one window in each habitable room generally needs to meet escape requirements — a clear opening of at least 0.33m², minimum 450mm in both height and width, with the bottom of the opening between 800mm and 1100mm above floor level. We specify the opening lights to meet this as standard.
What happens to my existing loft insulation?
It comes out. Insulation at ceiling-joist level is in the wrong place once the loft is a room — the thermal line moves up to the new roof and dormer build-up. We remove and dispose of the old quilt and insulate the new envelope, which is also what makes the room comfortable to use in August.
How much does a dormer window cost?
A single flat roof dormer typically runs from around £9,000 to £20,000 supplied and fitted, depending on width, cladding finish and access. A full-width rear dormer on a semi is usually £28,000 to £45,000, and a complete dormer loft conversion including stairs, insulation, plaster and building control sign-off is more commonly £40,000 to £70,000. Our online guide-price tool gives you an indicative range in about a minute.
Find out what your roof will take
A free measured survey tells you what is achievable, what it needs, and what it costs — before you commit to anything.